Replacing uPVC Window Handles
It is simple to swap the handles on windows made of upvc. It is important to make sure that the replacement handle fits the spindle that was cut out of the window mechanism.
If the steps below are followed properly the cockspur handle will be able to fit into most windows. The step height of the handle is crucial.
What to Do You Look For?
Many of the windows in the UK come with uPVC handles, and over time they may begin to show signs of wear and wear and tear. The handle on the window may become loose or difficult to operate when this occurs. This is a relatively easy task that is achievable by anyone who is comfortable using basic hand tools.
The first thing to do is ensure that the handle is securely connected to the window frame and is in the open position. The next step is to find the fixing screws or pins that hold the handle in place. They are typically located on the inside of the handle. They can be removed using an screwdriver or pliers.
Once the handle has become loose It is best to gently pull it away from its hinges. The next step is to find a new handle that is the same design and size. This can be accomplished online or at an area DIY store, and the process should only take around five minutes using a screwdriver.
When replacing the handle of a uPVC handle It is crucial to think about the step height. This is the distance between the handle's base and the place it is located in the window frame. This is a common measurement and you should check the height of the step before purchasing the replacement handle.
Depending on the type of handle you are using, there are different sizes that are available. Inline handles for uPVC windows usually feature lug centers of 31mm There are also handles with cockspur that have 43mm centres. Tilt and turn handles are commonly found on windows made of uPVC and they come with a unique design that allows the window to be tilted to allow for ventilation, and then turned to open the window fully.
The most common cause of breakage in uPVC handles is that they crack internally instead of breaking off from the base section. This can make them hard to open, and it is therefore important to make sure that any replacement handle you purchase has the same length of spindle that your current one.
Remove the old handle
If the handles on your windows are damaged or improperly fitted, they can cause double-glazed windows to open and close incorrectly. They could even become stuck. There are Read the Full Piece of writing including general wear and tear or corrosion of the handle made of metal. In these situations it is crucial to replace the window handle as soon as you can to prevent further damage or loss of functionality.
One of the first steps to do when replacing the handles on your windows made of upvc is to remove the old handle from the window. Begin by removing the screw covered by the handle while it is in the closed position. Once you have removed the screw, you can remove the handle. You can make the process easier by using an electric screwdriver.
You should also be aware that screws can be hidden in plastic caps. It is recommended to remove the covers using a Stanley knife. After the handle has been removed, take a look at the square cut out at the handle's base to ensure that the new window lock handles are compatible with it. This is important as you will need to measure the length of the spindle on the old handle to ensure it is in line with the size of the window mechanism and handle spindle that has been cut out.
The various types of window handles made of upvc are: Espag handles, which feature a central screw that will turn left or right; Cranked handles that have two screws and are typically found on tilt and turn windows made of upvc; and Spade handles, with a flat arm and can be placed on either side of the window. Once you have a suitable replacement, it is simply a case of screwing the handle into place and ensuring that the spindle is placed into the lock mechanism. Once that is done, it should be tightened to the window frame, and your new window handles made of upvc should be secure.
Measure the Spindle
If you need to replace a Upvc handle that has collapsed, it's likely the spindle holding it in place is damaged or loose. In some cases this can be fixed using screws or pins to tighten it. In some cases it might be necessary to replace the handle. There are several kinds of window handles made of upvc. They include espagnolette handles inline or cockspur handles. They also have tilt and turn handles. Each type of handle is mounted and replaced in a different fashion.
It is crucial to measure the handle before purchasing an alternative. This will ensure that the handle will fit the window in a proper manner and be the correct size. All handles are sized in accordance with industry standards, so it is easy to identify the correct size.
To measure the size of your handle, first remove it from the window by turning it to the open position. You should be able see the size of the screw or pin that secures the handle. Use a ruler or tape measure to determine how long the spindle is. Once you know the length of your spindle, it is possible to purchase a replacement that is the exact same length.
The step height of a upvc window handle is also important to take into consideration when buying replacements. The step height is measured from the base to the point at which the handle sits on the frame. This usually is around 21mm or 9mm in aluminium and uPVC. Dropping something into the space will allow you to observe how far the handle extends before it reaches an obstruction.
Cockspur handles come with different backsets depending on what type of window you put them in. Inline Espag handles have a standard height of 43mm from centre to centre (2 fixing points). Cockspur handles however, have different backset heights dependent on the style of the window they are in. This is due to the fact that they have a spur which extends from their handle and is locked onto a cockspur wedge striking plate.
Install the new handle
When you've picked a new handle, carefully align it to the screw holes in the door and fix it using the screws supplied. Install the latch lever the same way as the main handle when you're replacing the door handle. Then, attach the door trim to hide the screws for mounting.
Tips: To remove a metal head from a wooden wedge place the handle on the floor so that its wide end is on the ground. Then, you can use a hammer and tap the narrow end. Be careful not to scratch the handle or the spindle.